1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back.
article number
713212
Brodit holder fixed install. Honeywell EDA51
RRP
€111.95
- Fast Shipping
- High Quality Products
- Secure Payments
Keep your device installed in your vehicle and you will always have it within easy reach and sight! Safe and convenient, provides for a better work environment. Customized holder with a perfect, firm fit for devices with original case 50141376-001. With easy-switching system, which enables you to upgrade the holder only, and keep the installed cables. Saves you time and money!
An active holder which is to be connected inside the dashboard, this gives a discreet, neat installation without cables hanging over the interior! You can choose to use the holder as an active holder for charging of your device only, or to connect an adapter to the Molex connector for additional features. Then you can use the holder also for power supply of a GPS receiver or other own solutions (can not be used for data communication or audio connection). 12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. Professional installation recommended.
The holder is equipped with a tilt swivel so you can easily adjust the angle for better viewing, or switch between portrait and landscape mode. Tilts 17° and swivels 360°. Mounting plate 42x50 mm with 4 mm AMPS-holes. Made of high grade black ABS/Acetal plastic. Made in Sweden. Attach onto a high strength ProClip Mounting Platform or a Pedestal Mount.
Easy-switching system:
The easy-switching system enables you to upgrade the holder only, and keep the installed cables. It saves you a lot of time! When upgrading to a new device, you do not longer need to make a full installation. Same goes for maintenance in case of warranty or damage. You simply disconnect the holder from the charging cable via the Molex 6-pin quick connector, and then connect the new holder. The switch is done in a few seconds.
An active holder which is to be connected inside the dashboard, this gives a discreet, neat installation without cables hanging over the interior! You can choose to use the holder as an active holder for charging of your device only, or to connect an adapter to the Molex connector for additional features. Then you can use the holder also for power supply of a GPS receiver or other own solutions (can not be used for data communication or audio connection). 12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. Professional installation recommended.
The holder is equipped with a tilt swivel so you can easily adjust the angle for better viewing, or switch between portrait and landscape mode. Tilts 17° and swivels 360°. Mounting plate 42x50 mm with 4 mm AMPS-holes. Made of high grade black ABS/Acetal plastic. Made in Sweden. Attach onto a high strength ProClip Mounting Platform or a Pedestal Mount.
Easy-switching system:
The easy-switching system enables you to upgrade the holder only, and keep the installed cables. It saves you a lot of time! When upgrading to a new device, you do not longer need to make a full installation. Same goes for maintenance in case of warranty or damage. You simply disconnect the holder from the charging cable via the Molex 6-pin quick connector, and then connect the new holder. The switch is done in a few seconds.
| Accessory brand | Brodit |
|---|---|
| Barcode | 7320287132120 |
| Recommended retail price incl. VAT | €111.95 |
| Device with or without case | Without case |
| Holder feature | Device-specific |
| Cable / Qi / charger type / connnector | Molex, fixed install, piggy tail (Easy Switching) |
| Charge device via | Pogo pins |
| Input Voltage | 12/24V geschikt |
| Voltage (output) | 4.75 - 5.25V |
| Max Amperage | 2,0 Amp |
| Montage standaard | AMPS |
| Device holder lockable? | no |
| Color | black |
| Productinfo | Brodit houder |
Show more +
Show less -
Show more +
Show less -
1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back.
